Single row deep groove ball bearings are particularly versatile, have low friction and are optimized for low noise and low vibration, which enables high rotational speeds. They accommodate radial and axial loads in both directions, are easy to mount, and require less maintenance than many other bearing types.
| d |
10 mm
|
Bore diameter |
|---|---|---|
| tΔdmp | -0.007 – 0 mm | Deviation limits of mid-range bore diameter |
| D |
35 mm
|
Outside diameter |
| tΔDmp | -0.009 – 0 mm | Deviation limits of mid-range outside diameter |
| B |
11 mm
|
Width |
| tΔBs | -0.06 – 0 mm | Deviation limits of ring width |
| d1 |
≈ 17.5 mm
|
Shoulder diameter |
| D2 |
≈ 28.68 mm
|
Recess diameter |
| r1,2 |
min. 0.6 mm
|
Chamfer dimension |
|
P6 and tighter width tolerance
|
ISO tolerance class for dimensions |
| da |
min. 14.2 mm
|
Diameter of shaft abutment |
|---|---|---|
| Da |
max. 30.8 mm
|
Diameter of housing abutment |
| ra |
max. 0.6 mm
|
Radius of shaft or housing fillet |
| Basic dynamic load rating | C |
8.52 kN
|
|---|---|---|
| Basic static load rating | C0 |
3.4 kN
|
| Fatigue load limit | Pu |
0.143 kN
|
| Reference speed |
50 000 r/min
|
|
| Limiting speed |
32 000 r/min
|
|
| Minimum load factor | kr |
0.03
|
| Calculation factor | f0 |
11
|
| Range of section height at inner ring of assembled bearing | tKia |
4 µm
|
|---|---|---|
| Maximum run-out of inner ring side face to the bore | tSd |
7 µm
|
| Maximum axial run-out of inner ring of assembled bearing | tSia |
7 µm
|
| Range of section height at outer ring of assembled bearing | tKea |
7 µm
|
| Perpendicularity of outer ring outside surface | tSD |
4 µm
|
| Maximum axial run-out of outer ring of assembled bearing | tSea |
8 µm
|
| ISO tolerance class for geometrical tolerances |
P5
|
| d |
0.3937 in
|
Bore diameter |
|---|---|---|
| tΔdmp | -7 – 0 µm | Deviation limits of mid-range bore diameter |
| D |
1.378 in
|
Outside diameter |
| tΔDmp | -9 – 0 µm | Deviation limits of mid-range outside diameter |
| B |
0.4331 in
|
Width |
| tΔBs | -60 – 0 µm | Deviation limits of ring width |
| d1 |
≈ 0.689 in
|
Shoulder diameter |
| D2 |
≈ 1.1291 in
|
Recess diameter |
| r1,2 |
min. 0.0236 in
|
Chamfer dimension |
|
P6 and tighter width tolerance
|
ISO tolerance class for dimensions |
| da |
min. 0.5591 in
|
Diameter of shaft abutment |
|---|---|---|
| Da |
max. 1.2126 in
|
Diameter of housing abutment |
| ra |
max. 0.0236 in
|
Radius of shaft or housing fillet |
| Basic dynamic load rating | C |
1 915 lbf
|
|---|---|---|
| Basic static load rating | C0 |
764 lbf
|
| Fatigue load limit | Pu |
32 lbf
|
| Reference speed |
50 000 r/min
|
|
| Limiting speed |
32 000 r/min
|
|
| Minimum load factor | kr |
0.03
|
| Calculation factor | f0 |
11
|
| Range of section height at inner ring of assembled bearing | tKia |
4 µm
|
|---|---|---|
| Maximum run-out of inner ring side face to the bore | tSd |
7 µm
|
| Maximum axial run-out of inner ring of assembled bearing | tSia |
7 µm
|
| Range of section height at outer ring of assembled bearing | tKea |
7 µm
|
| Perpendicularity of outer ring outside surface | tSD |
4 µm
|
| Maximum axial run-out of outer ring of assembled bearing | tSea |
8 µm
|
| ISO tolerance class for geometrical tolerances |
P5
|
Reviews
There are no reviews yet.